Search results

Givi Monokey topbox rack SR371, adapter and plate. Fits Gen 1 and Gen 2. Comes used off my Gen 1 that I'm selling but in great condition. £35.

A Pyramid Hugger from my Gen 1. A bit of WD40 and it cleaned up really well. A few marks if you look closely, some rubbing where it fits behind the rear brake line but that will be hidden by your brake line, but otherwise in great condition. £30

Givi Airflow Screen bought for my Gen 1. 50k miles of use so there are some signs of wear from bugs and road dirt. £60.

I bought these Chinese levers for my Gen 1, but I'm pretty sure they will fit a Gen 2 along with a selection of other Yamaha bikes. I used a short one on the brake side for 2 finger braking and a long one on the clutch side. £15 for the lot.

I bought these Wind Deflector Wings for my Gen 1. They have a light tint and look as good as when I bought them. £30.

I bought this for my Gen 1, an SW Motech GPS quick release bracket that fits so the GPS is positioned above the clocks. The edges have started to rust so could do with a rub down with wet and dry and respray. £25.

I bought these heel protector plates for my Gen 1, I don't know if they also fit the Gen 2. There is some wear on them from my boots as can be seen in the photos. I bought them for two reasons, one being the original items gets scratched easily, the other so a trouser leg wouldn't easily get...

I'm selling my bike so have taken my Seat Concepts seat off the bike. I bought both main and passenger seat for the bike but only ever put the main seat on. The main seat cover therefore has some staple holes where it was attached to my seat but is otherwise in great condition. Both seats were...

The time has come to sell my S10. I have a KTM 1290 S on order which is 4 weeks away. I'm going to try and sell the bike fully loaded before I strip the goodies and sell them separately. The bike is listed on ebay at £6k https://www.ebay.co.uk/itm/252947356521

Took a KTM 1090 standard model out for a test ride today. The USA is not getting this model, this one is similar to the 1090R but with 19/17 alloy wheels instead of 21/18 wire spoked and front suspension that cant be adjusted. First off I was concerned about the front forks as the standard bike...

I have 1.0 and 0.9 springs at home ready for use, one pair of which I intend fitting on Thursday along with some Andriani fork pistons. I bought the 1.0's when I was around 320 pounds but never got round to fitting them, I'm now down to 260 and losing 10 pounds a month. The question is, do I...

My new RoadAttack 2 EVO rear tyre developed some cracks/tears around the tread pattern after around 1000 miles on my S10 and has been replaced with an identical tyre free of charge. Perhaps it was a one-off problem, perhaps not, but I suggest if you have this tyre you check yours. I will report...

I see Andreani do a fork piston kit for the S10, has anyone tried it out?

Just over one year old, 22,500 miles, and I've just had a headlight bulb blow. Should I chop it in for another bike as this blown bulb is worrying me that the whole thing is now going to fall to pieces? :)

Just changed my tyres again (to Avon Storm XMs), here's the mileage I got on the Super Tenere on the two types of PR4... PR4 Front - 10,842 (i.e. two rears, was some mileage left on it but it was starting to feel a little loose so changed it anyway). PR4 Trail Rear - 4,822 (around 500 miles...

New tyres from Continental... http://www.conti-bike.co.uk/default.asp?spid=71

I booked my bike in a month ago to have the warranty headlight harness repair on Monday. Last Friday the dealer (Fowlers in Bristol) called to cancel the appointment as they had not had a harness through and said Yamaha UK had no stock.

I've put some Carnuba wax on the screen and headlight lenses which makes bug removal easier, but having a matt grey bike I don't intend putting wax on that. Any handy tips on bug removal other than soap, water and elbow grease?

Has anyone changed the spring on the standard shock? Will the damping on the shock stand up to a large change in spring rate? I know a new shock from a suspension specialist would be the best solution, but at a quarter of the cost would an upgraded spring be "good enough"?

Can I use the black and blue/black (or black/green) wires on the heated grip socket to directly power my oxford grips, ie is the wiring good enough, or do I need to use the connector to fire a relay and run a feed from the battery through the relay. On the same basis I'd like to use the...