What you did to your Tenere today??!!

[Muggy]

I had a busy week. I added:
Oxford heated grips

Madstad supports
Yamaha LED turn signals.

New boots Shinko 705s
Gave her a quick bath

 

[Kevhunts]

New Mitas E07 Dakars Front and Rear. Rox risers.

Couldn't help but notice you are running Gen1 Rox risers on a Gen2 bike. You may want to upgrade for increased safety and reduced puckering effect .

 

[Fpalbrecht]

Thanks for the heads up. I ordered them from revzilla.com, explained what bike I had and that's what they sent. I called Rox to verify what you said and they agreed. Called revzilla.com back, they apologized and are sending me the correct part 2 day shipping. Thanks again.

 

[Dogdaze]

Thanks for the heads up. I ordered them from revzilla.com, explained what bike I had and that's what they sent. I called Rox to verify what you said and they agreed. Called revzilla.com back, they apologized and are sending me the correct part 2 day shipping. Thanks again.

No, it's a Gen 1 bike with Gen 1 risers. The LED flasher are not OEM and the speedo is Gen 1. So all good. Anyway, Gen 1 risers will never fit a Gen 2 bike, angles are all wrong.

 

[Fpalbrecht]

Actually they fit good. Didn't notice any angle issues. But Rox told me that the part that fits into the stock holder will be longer.

 

[Kevhunts]

No, it's a Gen 1 bike with Gen 1 risers. The LED flasher are not OEM and the speedo is Gen 1. So all good. Anyway, Gen 1 risers will never fit a Gen 2 bike, angles are all wrong.

I think you are looking at the wrong post.

 

[Dogdaze]

I think you are looking at the wrong post.

You are right sir, my bad ::010:: But how did those even fit without at least some pushing and shoving???

 

[Fpalbrecht]

If you're talking about the risers they fit great. Just hooked them up. Would have never known if you hadn't pointed it out.

 

[Fpalbrecht]

Got the correct risers yesterday. Installed them. After installing both, the correct version is definitely better, lol. I really like how this bike feels now standing on the pegs with the risers. Will try it out at March Moto Madness in Tellico Plains next week.

 

[hogmolly]

OK....cut 2" from a PUIG screen. Added OEM bars and after removing all the side panels, tank I discovered I didn't need to do any of that. Put on an ALTrider tailpiece/pillion piece.

 

[fac191]

Had the 6000mls service, new Roadsmart 3`s fitted and put the winglets on. Getting ready for the Highlands !

 

[Matt101]

Finally found some time to fit a few bits I've been hoarding. Crash bars, driving lights and spotlights. Also one of Bernies dashboards. Great bit of kit. I decided carbon wrap was the order of the day. Also added a direct to battery charging point. Glad with how it all turned out.

The spot are very bright. Well worth the money off Amazon.

Just got to change the rear fender because the bike shop mounted the RS4 in the wrong place!!!!

 

[BWC]

Looks good trimmed out in the carbon fibre.
Those engine guard mounted lights look very much like the 10watt "cost effective" ones I bought to mount on my wife's 650 for daytime running. Looks like one of the last things left to do is work on that odometer. It could use a few more digits. ::008::

 

[Boris]

Finally found some time to fit a few bits I've been hoarding. Crash bars, driving lights and spotlights. Also one of Bernies dashboards. Great bit of kit. I decided carbon wrap was the order of the day. Also added a direct to battery charging point. Glad with how it all turned out.



Just got to change the rear fender because the bike shop mounted the RS4 in the wrong place!!!!

Berries dashboards? Where can I get one of these?

Ta

 

[Matt101]

Looks good trimmed out in the carbon fibre.
Those engine guard mounted lights look very much like the 10watt "cost effective" ones I bought to mount on my wife's 650 for daytime running. Looks like one of the last things left to do is work on that odometer. It could use a few more digits. ::008::

They are not so cheap ones. Feel a little stung over them but they work well so we'll see. That dash though is awesome. Can reach the button no problem.
And the Odo will be getting some miles on it in the coming months. Got a trip to Scotland and one to Ireland pencilled in for this year!!

 

[Matt101]

Berries dashboards? Where can I get one of these?

Ta

From BWC (the same member posting above). He has stopped production but maybe someone has one gathering dust in a garage somewhere so may be worth a post on the Wanted page.

 

[hogmolly]

My little homemade inner rear fender....works good.

 

[Xt1200zsupertenere]

Just some black matte paint and connect

 

[Don in Lodi]

Just some black matte paint and connect

Can you post the manufacturer of that meter please?

 

[Matt101]

Can you post the manufacturer of that meter please?

Looks like this one

https://www.amazon.co.uk/BANDC-Waterproof-Motorcycle-Digital-Voltmeter/dp/B06W5PW6V5/ref=sr_1_5?ie=UTF8&qid=1490638031&sr=8-5&keywords=waterproof+voltmeter