Search results

I would get the Z and the upgrade the suspension. The ZE's suspension is not better than the Z's, it's only electromechanical. Of this makes sense, you may what to search for STOLTEC and TRAXXION DINAMICS.

Humm... Man it is just easier to install a switch to bypass the fuse....

We have used PUIG grips installed into the Yamaha V2 wires and they work just fine.

No sir. The heated grips are black and grey with two wires heach. The one for the auxiliary lights is the triple. I don't know what is the one with 4 wires for. I ha e used it for power as it has a +/- wires. You can buy these plugs on Ebay or Amazon. Sorry I don't have the link, I...

80 MPG is about 125 kmts per gallon, equal to approximately 25 kmts per liter. That's a lot. Do we get that amount of tarmac per liter? I do ride at 8000 feet.... Saludos from Bogotá, Colombia. XT1200Z/2014 WR250F/2014 BMW 9T/2015

Hola, one friend did the install, but Yamaha's technician cut the resistors and ruined the system. The biking rate was fast. We found a set of resistors and reinstall them but the blinking rate did not become normal. We will need to USA a 50 ohms 20 watts resistor per side, or change the...

Re: Yamaha Heated Grip Installation Ok, so with the non OEM we have not seen any difference between each grip. Indeed, the PUIG control does not match colors or sides. Either way is OK with that set. We did not check for left and right. It seems to me it does not matter; if it did, the OEM...

Re: Yamaha Heated Grip Installation Hola Gaps, OEM grips come also with two color coded, but I did not see any indication of a maching colors when installing so I did it really checked that. I do, however, believe the two grips are the same. I do not see how the throttle tube could affect the...

Re: Yamaha Heated Grip Installation Right on. On my 2014 ST I have the OEM grips. I measured resistance and both grips are the same. For the non OEM (in this case the PUIG) both of them measured the same resistance, as the OEM. I cannot recall values. So as you asked, we just connected...

http://www.yamahasupertenere.com/index.php?topic=12822.0 Yamaha Heated Grip Installation Basically is just plug each pair of wires from each grip to the pre installed conectors, black and grey, as I show on the pictures. We made a movie, my friend is editing it, I will post it for you guys...

Today we installed a pair of PUIG Heated grips into the OEM conectors of a ST 2014. It worked just fine, dash board control operated perfectly. Saludos from Bogotá, Colombia. XT1200Z/2014 WR250F/2014 BMW 9T/2015

Re: Yamaha Heated Grip Installation Today we installed a pair of PUIG Heated grips into the OEM conectors of a ST 2014. It worked just fine, dash board control operated perfectly. Saludos from Bogotá, Colombia. XT1200Z/2014 WR250F/2014 BMW 9T/2015

I was also skeptical about suspension MOD. But I did it, with Stoltec . I have both front cartridges redone and my rear shock totally replaced. I must say I absolutely love it and I do think is the best mod one can have. Regarding Stoltec, it is a Penske system, with new linear springs...

Re: Folding Shift Lever: <$30 and <1 hour And then, after one month it broke again. What a piece of junk. It broke at the same spot. And also, the spring of the foldable lever broke. It is junk

Please look at the fuel filter MOD http://www.yamahasupertenere.com/index.php?topic=1832.msg218219.msg#218219

Guys, I recently learned that it is totally possible to change just the fuel filter. Guys in my country, Colombia, had worked out the filter problem and they have done this mode on XT1200Z, XT660Z, R, and in MT07 and MT09. Recently I was with my pals on the second national Super Tenere national...

Took my ST to the beautify Coffee District in western Colombia, for the anual ST meeting, sponsored in part by Yamaha. Some pics. We will be about 70 bikes.

I had an GS1100 once, I put 50.000 miles on it. Now I own a ST. To make a long story short, the ST, compared to a GS, is like a mistress: it costa me half the money and, as the ST is much more reliable, I have a much a twice the fun. Does it make sense?

Installed a OEM set of heated grips on my ST 2014. They work just fine with the control panel and handle bar controls. Expensive but functional.

Did you check the brake and clutch lines? Do they reach fine?