Recent content by Juan Valderrama

I would get the Z and the upgrade the suspension. The ZE's suspension is not better than the Z's, it's only electromechanical. Of this makes sense, you may what to search for STOLTEC and TRAXXION DINAMICS.

Humm... Man it is just easier to install a switch to bypass the fuse....

We have used PUIG grips installed into the Yamaha V2 wires and they work just fine.

No sir. The heated grips are black and grey with two wires heach. The one for the auxiliary lights is the triple. I don't know what is the one with 4 wires for. I ha e used it for power as it has a +/- wires. You can buy these plugs on Ebay or Amazon. Sorry I don't have the link, I...

80 MPG is about 125 kmts per gallon, equal to approximately 25 kmts per liter. That's a lot. Do we get that amount of tarmac per liter? I do ride at 8000 feet.... Saludos from Bogotá, Colombia. XT1200Z/2014 WR250F/2014 BMW 9T/2015

Hola, one friend did the install, but Yamaha's technician cut the resistors and ruined the system. The biking rate was fast. We found a set of resistors and reinstall them but the blinking rate did not become normal. We will need to USA a 50 ohms 20 watts resistor per side, or change the...

Re: Yamaha Heated Grip Installation Ok, so with the non OEM we have not seen any difference between each grip. Indeed, the PUIG control does not match colors or sides. Either way is OK with that set. We did not check for left and right. It seems to me it does not matter; if it did, the OEM...

Re: Yamaha Heated Grip Installation Hola Gaps, OEM grips come also with two color coded, but I did not see any indication of a maching colors when installing so I did it really checked that. I do, however, believe the two grips are the same. I do not see how the throttle tube could affect the...

Re: Yamaha Heated Grip Installation Right on. On my 2014 ST I have the OEM grips. I measured resistance and both grips are the same. For the non OEM (in this case the PUIG) both of them measured the same resistance, as the OEM. I cannot recall values. So as you asked, we just connected...

http://www.yamahasupertenere.com/index.php?topic=12822.0 Yamaha Heated Grip Installation Basically is just plug each pair of wires from each grip to the pre installed conectors, black and grey, as I show on the pictures. We made a movie, my friend is editing it, I will post it for you guys...

Today we installed a pair of PUIG Heated grips into the OEM conectors of a ST 2014. It worked just fine, dash board control operated perfectly. Saludos from Bogotá, Colombia. XT1200Z/2014 WR250F/2014 BMW 9T/2015

Re: Yamaha Heated Grip Installation Today we installed a pair of PUIG Heated grips into the OEM conectors of a ST 2014. It worked just fine, dash board control operated perfectly. Saludos from Bogotá, Colombia. XT1200Z/2014 WR250F/2014 BMW 9T/2015

I was also skeptical about suspension MOD. But I did it, with Stoltec . I have both front cartridges redone and my rear shock totally replaced. I must say I absolutely love it and I do think is the best mod one can have. Regarding Stoltec, it is a Penske system, with new linear springs...

Re: Folding Shift Lever: <$30 and <1 hour And then, after one month it broke again. What a piece of junk. It broke at the same spot. And also, the spring of the foldable lever broke. It is junk

Please look at the fuel filter MOD http://www.yamahasupertenere.com/index.php?topic=1832.msg218219.msg#218219