MileageMonster
Well-Known Member
Added a Puig clip on today.
Previously: TomTom-Rider holder, X-grip for cell-phone.
Yet to come: A set of Bumot panniers and top-case, Altrider lower crash bar, full set of tankpads.
What you did to your Tenere today??!!
- Thread starter biting_point
- Start date
Added a Puig clip on today.
Previously: TomTom-Rider holder, X-grip for cell-phone.
Yet to come: A set of Bumot panniers and top-case, Altrider lower crash bar, full set of tankpads.
Dons 1911
Well-Known Member
How ya gonna keep that thing upright now? Ain't she gonna list to the port side? LOL
very nice did similar with PETG to make a design for mounting the external drivers, also playing with water/oil seperator fabric to stop water and dust but let air into them to help cool the leds. still gotta work on my design as what i created works but didnt realize the alignment on the right and left side were diffrent so the box sits at diffrent angles when installed vs what i planed on in the design.
Last edited:
what kind of hooks/loops are you using want to do the same but not pay for the over priced version the make of my boxes want to charge to add something like this.
I used these ones because they were a good combo of larger bolt eye size and smaller D-ring size.
If I did it over again, I might shoot for some that have an 8mm bolt eye opening on the retainer. I also didn't want them to be too thick under the bolt, since there's so very little remaining bolt thread for the nylock (and I didn't want to replace the bolts).
gapmtn1
Active Member
Put an Alt Rider skidplate on this weekend.
It was not a difficult install, but I foresee future oil and filter changes being a bit more fiddly in the future. Rode a short distance between two stops without earplugs and at one point was moderately alarmed about the engine noises I was hearing.
It was not a difficult install, but I foresee future oil and filter changes being a bit more fiddly in the future. Rode a short distance between two stops without earplugs and at one point was moderately alarmed about the engine noises I was hearing.
Onenoodles
Active Member
Nice day in the UK today and I am off work 
so took myself off to Teignmouth Devon for a quick hour on the beach (sunny but pretty chilly though!) and then back through Cheddar Gorge and stopped to watch the climbers practising(rather them than me)
A nice day on the bike and I grow fonder of it by the day ....
so took myself off to Teignmouth Devon for a quick hour on the beach (sunny but pretty chilly though!) and then back through Cheddar Gorge and stopped to watch the climbers practising(rather them than me)A nice day on the bike and I grow fonder of it by the day ....
PhilPhilippines
Well-Known Member
I always go through Cheddar Gorge when I visit one of my best friends in the world, and resident of Teignmouth!!Nice day in the UK today and I am off work
A nice day on the bike and I grow fonder of it by the day .... View attachment 79433View attachment 79429View attachment 79430View attachment 79431
Onenoodles
Active Member
ooooops .... just realised that this post should have gone in the 'Where did you take your Tenere Today' thread .... soz everyone!
yen_powell
Well-Known Member
My Altrider bash plate makes high pitched noises at certain rpm, sometimes I even think I can hear a siren. When it comes off for the next oil change I am either going to stick a bit of rubber matting on the large alloy bottom (inside) or stick some wheel balance weights across it to stop it vibrating and producing the noises.
jhansen
Active Member
@Onenoodles..a bad day at the beach beats a good day at work. great pictures
Onenoodles
Active Member
She is hard not to like. Gorgeous roads. I now hate you.
would still swap you for touring around some USA states ... my favourite country of all, not been to Texas yet but its on the list!