A Pyramid Hugger from my Gen 1. A bit of WD40 and it cleaned up really well. A few marks if you look closely, some rubbing where it fits behind the rear brake line but that will be hidden by your brake line, but otherwise in great condition. £30
I bought these Chinese levers for my Gen 1, but I'm pretty sure they will fit a Gen 2 along with a selection of other Yamaha bikes. I used a short one on the brake side for 2 finger braking and a long one on the clutch side. £15 for the lot.
I bought this for my Gen 1, an SW Motech GPS quick release bracket that fits so the GPS is positioned above the clocks. The edges have started to rust so could do with a rub down with wet and dry and respray. £25.
I bought these heel protector plates for my Gen 1, I don't know if they also fit the Gen 2. There is some wear on them from my boots as can be seen in the photos. I bought them for two reasons, one being the original items gets scratched easily, the other so a trouser leg wouldn't easily get...
Re: (UK) Seat Concepts Gen 1 Front and Passenger Seat
Here are some more photots.
Underneath of main seat cover showing staple holes:
Front underneath of main seat cover showing staple holes:
Top of main seat foam:
Bottom of main seat foam:
Don't have any pictures of the bottom of the...
I'm selling my bike so have taken my Seat Concepts seat off the bike. I bought both main and passenger seat for the bike but only ever put the main seat on. The main seat cover therefore has some staple holes where it was attached to my seat but is otherwise in great condition. Both seats were...
The time has come to sell my S10. I have a KTM 1290 S on order which is 4 weeks away. I'm going to try and sell the bike fully loaded before I strip the goodies and sell them separately. The bike is listed on ebay at £6k https://www.ebay.co.uk/itm/252947356521
Took a KTM 1090 standard model out for a test ride today. The USA is not getting this model, this one is similar to the 1090R but with 19/17 alloy wheels instead of 21/18 wire spoked and front suspension that cant be adjusted.
First off I was concerned about the front forks as the standard bike...
I got 9k miles out of Roadsmart 3 rear and I could have probably got another 1k. Mostly multi-lane highway use. Grip is good wet and dry. By comparison I got 6k from a PR4, 10k from Avon Storms (didn't like them), 11k from Roadsmart 2s (prefer the Roadsmart 3s).
Take baffle out, try putting some tape over a couple of the holes, try it for noise, chop and change till you like it, then get some welding to make a permanent change to the baffle.
I ran a full arrows without a flash, it ran just fine other than a little uneven at very low throttle openings (caused by downpipes not silencer). Rasher ran just the downpipes with the OEM silencer and experienced the same unevenness when riding slowly at low throttle openings. You can slip the...
Maybe the US importer has changed and they are temporarily unavailable in the US, but they are still making them... http://www.arrow.it/en/assembled/1023, and have a look at eBay.it or eBay.co.uk for 72095pd, you maybe able to get one shipped to you. I bought mine from Italy via eBay.
Thanks, was 315 last December, started a diet properly in March, down to 215 now, heading for 185'ish at 6'4. Feels great, only wish I had done it years ago.
Managed to trim 100 pounds off mine this year, all on top of the saddle. Can't say it has made a huge difference, perhaps to the acceleration from standing, and definitely to the riders health.
I had my bike done at Hilltop, I wouldn't recommend them, it didn't make much of a difference.
I imported my clutch basket from partshark.com, a better exchange rate when I bought it. Made a huge difference and definitely recommended.