Recent content by Wistrick

  1. W

    4.8 gallon aux fuel cell

    Sale Pending!!!
  2. W

    4.8 gallon aux fuel cell

    This is a 4.8 gallon EAZ Cycle (google) flat bed fuel cell for the Gen1 and 2 Super T... PM or danieldyer2008@gmail.com tank has been paint since this picture and antenna mount rmoved Price is $400.00 plus shipping
  3. W

    Carbon Build up what causes it...

    So I checked my valves and set them to the middle of the range at 40k and installed a MCCT....am I gonna get 100,000 out of this motor??? Or am I gonna be in for a rebuild @ 80K ????....bike will have 60k soon so i am concerned.....
  4. W

    Carbon Build up what causes it...

    So why did u have to tear in to your motor at 83K?????
  5. W

    Carbon Build up what causes it...

    Keep seeing issues with higher mileage bikes with carbon build up causing engine issue with the S10....Also seen LongHaul Paul and others run these motors 100,000+ miles with no such issues so what gives....I suspect the 2 biggest issues are running at lower revs and never getting bike to red...
  6. W

    GpX Pro gear indicator

    So the instruction from the other threat read as followsTo install the Gear Position Indicator GiPRO-X (aka GPX) do the following: 1) follow the steps above, EXCEPT you DO NOT CUT the BLUE wire. The WHITE lead from the GPX is simply tapped into the BLUE wire using the supplied POSI-LOC tap...
  7. W

    Gear indicator tap wires

    the FPX -Pro indicator tap wires....All the previous threads pictures are gone.... both connections are suppose to be on the left ecu connector.... I can't find a solid blue wire they all have either stripes or dots on them...I did find a Blue with not strip but it had brwn and white dots....And...
  8. W

    torquing the clutch cover

    the service manual show a tight ing sequence going over each bolt 2 to 3 times...question do I hit it with the 9.6 ft pounds each time or just part of it??? confused.... Dan
  9. W

    MCCT adjustment

    I turned the tensioner in tell I had tension then held the bolt in place while turning the motor checking for slack, then back it out a 1/4 turn...per this video... http://www.youtube.com/watch?v=43uLWGSbLuk&t=855s only issue I have now is it seems the clutch gasket didn't survive cause...
  10. W

    MCCT adjustment

    for what its worth I decided to adjusted mine (APE unit) per there website instructions... INSTRUCTIONS To set the tensioner adjustment, rotate the engine forward while screwing the tensioner bolt in. When you feel the engine tensioner parts (guide, rollers, etc.) make contact with the moving...
  11. W

    MCCT adjustment

    based on this and other instruction I read, I pulled the clutch cover and rotated the motor, the chain it tight on the guide all the way around....so I re adjusted as follows... turned it in finger tight tell I felt tension and back it out 1/4 turn... thoughts??? Dan
  12. W

    MCCT adjustment

    worried that I adjusted it to tight, but don't hear a whizzing sound that would indicate that....??? Dan
  13. W

    MCCT adjustment

    so are you saying you adjusted the same way 1/2 turn in after tension opposed to 1/2 turn out
  14. W

    MCCT adjustment

    I installed a manual CCT last valve check...an APE unit...From everything I have read the adjustment should be tension on the guide then backed off 1/2 turn...Thing is my buddy who helped with the install said it should be turned in 1/2 a turn... Bike runs fine with not weird noises or rattles...
  15. W

    Replacement grips

    sorry to bring up an old topic but, for those using Progrip 714's they appear to be closed end grip are you just cutting the end off??? Dan
Top