Recent content by duartesss

Hello, in the ZE(ES) version, in HARD position +3 is harder and -3 is softer. But in SOFT, which one is softer: +3 or -3 ? Thanks Duarte S.

Is from 2014...but perhaps you do not know it... in Brazil some journalists accepted the challenge to ride a Super Tenere in the 500 miles of Interlagos against sport bikes and, in the end, they finished in 6th place...: https://youtu.be/4qjqkcwi10Q And after that the same guy accepted the...

Hello, I have a Super Tenere 2014 ES(ZE) with ECU Flashed. I like in this bike: - the handle of the bike in low speeds and small spaces - the handle in lows rev: without the need to do much shifting gear work when in low rev - is much comfortable - the shaft - handle well with the engine...

Hello, - The kind of off-road that I will want to do will be this one: https://youtu.be/xoQ-Oq1bXvI For this video they used the stock Bridgestone Battle Wings, that are essentialy on-road - On-road I will not intend to ride with high speed, because I opted for a relaxed and defensevely ride...

They do a detailed analysis of each one. Quickly draft translation of the general conclusion : In the end of the day of testing and contrasting the sensations, the four of us clearly match in almost every aspect of each machine. By assessing the effectiveness and ease of operation on Off...

The guys from a Spanish magazine did an off-road comparison between S10, AT, GS1200 Adv and KTM 1190 R. They equipped all the bikes with knobby tyres and each brand (Honda, Yamaha, etc) send a rider sponsored by each one (all Dakar ones that already participated in several editions). In end...

I installed 1 3/4'' Rox Risers on my ST 2015 ZE(ES) using the Altrider adaptor kit. Also moved a litle bit the clutch lever to right and the break lever to right in the bar and do not have problems with the cables... However I have the feeling the bike is now not so safe to manage, essentially...

I installed 1 3/4'' Rox Risers on my ST 2015 ZE(ES) using the Altrider adaptor kit. Also moved a litle bit the clutch lever to right and the break lever to right in the bar and do not have problems with the cables... However I have the feeling the bike is now not so safe to manage, essentially...

Hello, I also installed the Off-The-Road Clutch slave cylinder and I'm using it since some time ago... To be honest I didn't noticed any clear improvement in relation with the original clutch cylinder that comes with the bike... Sometimes I have the felling that I even have to apply more...

Hello, of course that I followed before all the steps in this manual, but simple do not works...I tried, also others tried, but not works... And the supplier that forward my video to Givi and is waiting (about a week now...) for a solution...

Hello, I have a 2016 ST ZE (ES), and I'm facing these problems to install the PL2119CAM support for the Trekker Outback cases: https://youtu.be/LV_O70QEASg Any of you had the same issue? How was solved? Thanks!! Duarte S.

Hello, I have a 2016 ST ZE (ES), and I'm facing these problems to install the PL2119CAM for the Trekker Outback cases: https://youtu.be/LV_O70QEASg Any of you had the same issue? How was solved? Thanks!! Duarte S.

Hello, do you know if I can use a Top-Case Givi Trekker Outback 58 lts with an AltRider Rear Luggage Rack ? Thanks! Duarte S.

Hello, someone told I can place two ADV Helmets inside a Givi Trekker TRK52 Top Case if I laydown the helmets (not in upright position). Do you know if this is really possible? I have two Nexx XD.1 helmets... Thanks Duarte S.

Hello, Seems that you are using the Top-Case Givi Trekker Outback 58lts with an Altrider rack...Is correct? If yes, boths (case and rack) works well ? Thanks Duarte S.