Yamaha Super Ténéré Forum
Log in
Register
What's new
Search
Search titles only
By:
Menu
Yamaha Super Ténéré Forum
Log in
Register
What's new
Search
Search titles only
By:
Home
Forums
New posts
Search forums
What's new
New posts
New media
New media comments
New profile posts
Latest activity
Media
New media
New comments
Search media
Members
Member Map
Current visitors
New profile posts
Search profile posts
Search titles only
By:
Member Map
Current visitors
New profile posts
Search profile posts
Home
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
~TABASCO~'s latest activity
~TABASCO~
reacted to
gv550's post
in the thread
McCRUISE fitted today but have issues
with
Like
.
I'd be more concerned about the aftermarket sensor, install a known working Yamaha sensor before changing other parts. And I agree with...
Yesterday at 10:35 AM
~TABASCO~
reacted to
Cycledude's post
in the thread
McCRUISE fitted today but have issues
with
Like
.
What happens when the Mc Cruise is completely removed and put back to factory stock ?
Yesterday at 10:32 AM
~TABASCO~
replied to the thread
McCRUISE fitted today but have issues
.
This is because the bike is running on its start up run / worm up software..... Once its goes thought this "start" software and its...
Yesterday at 10:29 AM
~TABASCO~
reacted to
gv550's post
in the thread
Whining noise from engine.
with
Like
.
Yes, I had a flashlight above and caused the oil to shine a bit silver. Here's the same pleat with no flashlight. There are no metal...
Yesterday at 8:47 AM
~TABASCO~
replied to the thread
Whining noise from engine.
.
It looks like silver metal in the “V” portion of the pleat? Is that just “optical” with the camera. Looks like it’s full of silver...
Tuesday at 10:52 PM
~TABASCO~
replied to the thread
Whining noise from engine.
.
OK. Let “us” know what the pleats of the filter look like. Look at them with a flash light. ‘Torch’ If it was my bike I would pull...
Monday at 10:50 PM
~TABASCO~
replied to the thread
Whining noise from engine.
.
Ha-Ha..... Yes Sir ! ? If it was at my shop I would: 1) Cut open the oil filter... take a look in the pleats.... Look for anything...
Monday at 4:20 PM
~TABASCO~
replied to the thread
Fork seal replacement
.
RCinNC just mentioned the seal cleaner.... I agree with what he mentioned........ I will add, with my experience with the Tenere...
Monday at 11:17 AM
~TABASCO~
replied to the thread
Can Someone Identify These Wires ?
.
You can run the little Aux plug power for GPS. You can also use that as a power trigger for a relay. You can’t power a light bar...
Monday at 6:31 AM
~TABASCO~
reacted to
Tenman's post
in the thread
Can Someone Identify These Wires ?
with
Like
.
That is the recall job
Monday at 6:29 AM
~TABASCO~
replied to the thread
Fork seal replacement
.
No not hard. The top ‘nut’ is something like 43 mm I believe. I’ll have to go double check. Make sure to change out the guides if...
Saturday at 9:39 PM
~TABASCO~
replied to the thread
Revalve, broken peening. Game over?
.
Fantastic ! Sounds like it's going in a positive direction !
Friday at 5:31 PM
~TABASCO~
replied to the thread
Revalve, broken peening. Game over?
.
Makes sense.... Have you found the cause yet ? Reason why ? I would suggest looking at that top out spring and make sure its not...
Friday at 1:47 PM
~TABASCO~
reacted to
kjetil4455's post
in the thread
Revalve, broken peening. Game over?
with
Like
.
Check valve was torsioned and stuck open. On rebound valve. the clunking was the top-out spring topping out hard and fast.
Friday at 1:45 PM
~TABASCO~
replied to the thread
Revalve, broken peening. Game over?
.
Just for reference.... Here is the "stock" Ohlins top out springs I pulled out.... Yep, your 100% correct ..... neither picture is...
May 2, 2024
Home
Members
Menu
Log in
Register
Forums
What's new
Log in
Register
Search
Top