What you did to your Tenere today??!!

[MFP]

Givi Trekker Outback and Denali brake light. Not a bad morning. Got to say, the Denali brake light is pretty darn bright. I almost got rid of the relector and put the additional brake light above the license plate. But decided to put it down below.


View attachment 59483View attachment 59484

View attachment 59482

Givi Trekker Outback and Denali brake light. Not a bad morning. Got to say, the Denali brake light is pretty darn bright. I almost got rid of the relector and put the additional brake light above the license plate. But decided to put it down below.


View attachment 59483View attachment 59484

View attachment 59482

TxCodeMonkey,
Was the Denali B6 Brake Light a fairly straight forward install with the wire splicing?
The Denali looks like a real cleanly designed unit.

 

[Tenman]

teman,

what anti-seize do you use i have a altrider on order.

rob

Mine is still seized on there. It's got some slack in it.

 

[TxCodeMonkey]

TxCodeMonkey,
Was the Denali B6 Brake Light a fairly straight forward install with the wire splicing?
The Denali looks like a real cleanly designed unit.

The hardest part was figuring out which loom to cut. Once there I removed about 2-3mm of insulation on each wire, staggered. I wrapped the Denali wire onto the S-ten wires, then soldered them. I am not fond of the wire vampires. The ones included look really good, and I used them for testing. But nothing is going to be more durable than good old lead-alloy solder.

 

[bimota]

Mine is still seized on there. It's got some slack in it.

I have a tub of copper slip, grease would this be ok

cheers rob

 

[Tenman]

Installed Red Winglets to match my Red Bike.

View attachment 59415

View attachment 59416

View attachment 59417

I see a brake line zip tied to your handlebar riser. Is that an update? My gen 1 doesn't have it.

 

[Super08]

He has a riser kit on it and has extended the brake line. The extension comes with the Helibars kit on Gen 2 bikes.

 

[Madscrapper85]

Well did a little of everything today. Bar risers 25mm, oil change, final drive fluid change, mounted an ankee 3 front tire and a scorpion trail rear, and installed a USB charger volt meter where the stock port was. Oh and put in some LED headlights. No wonder I'm tired

 

[elricfate]

He has a riser kit on it and has extended the brake line. The extension comes with the Helibars kit on Gen 2 bikes.

Yep

 

[Tenman]

I've got long lines from Ride on Adv. They don't have the fitting. What is it for?

 

[elricfate]

I've got long lines from Ride on Adv. They don't have the fitting. What is it for?

It's just to extend the brake line. Clutch line only needs a small adjustment. Eventually I'll get longer braided lines but this works well

 

[Tenman]

If its workin run it

 

[Davesax36]

Cooked my final drive.

Sent from my SM-G955U using Tapatalk

 

[elricfate]

Cooked my final drive.

Sent from my SM-G955U using Tapatalk

How did you manage that? No gear oil?

 

[bimota]

Changed my gen1 side stand over to a gen 2 alloy one side stand was £39 altrider foot £40 £79 in total great improvement.

 

[Davesax36]

How did you manage that? No gear oil?

Apparently... The drain plug is gone, soooooo. I'll post pics when it's all apart.

 

[holligl]

Apparently... The drain plug is gone, soooooo.

Self inflicted or dealer?

Sent from my SM-N950U using Tapatalk

 

[regder]

Apparently... The drain plug is gone, soooooo.

That's a bummer. At least used ones can be had for a couple hundred off ebay

 

[EricV]

Self inflicted or dealer?

Or vandalism?

 

[Davesax36]

Or vandalism?

Must have been self inflicted. Lots of things happened while we were prepping to move, and I shipped the bike. Didn't think about it until things suddenly started sounding bad. Won't happen again. Also glad I didn't have to learn this lesson in a more difficult way.

 

[elricfate]

I stripped the plug off my C90 once. I ended up getting a size up in thread pitch oil plugs and then tapped it for the new size. Worked a treat.