Search results

One of my sensors is letting a little exhaust gas escape. Are there any known issues with sensors leaking or is it simply needing nipped up? Anyone know torque for sensor into exhaust? TIA

At work, limited search ability. looking for part number for oil seal in shaft drive, the one

When you lift the filler cap, the inside rim of my tank filler neck is showing some corrosion. Never had this on a bike before. Want to sort this before it gets out of hand. What would cause the corrosion? How best to remove and seal to prevent fresh surface rust? TIA

Looking for an end can. Something a bit sweeter sounding than oem can. Anyone have one they'd part company with? TIA

Sidi Adventure boots in black. Size euro 47 / UK 12 - I am normally a shoe size euro 45 UK 10 1/2 but Sidi are renowned for being a small fit. For me, these are good with ordinary socks but allow a little wiggle room for thick socks for riding in colder weather. In very good condition with no...

Wee run out on some of Scotlands finer minor roads and inevitably a stone smashed the lens on one of my PIAA spot lights. Has anyone got either the glass lens for one of these or a whole singal spot light available to sell me? TIA

As I have limited t'Internet skills, I've been unable to find the torque wrench settings for the rear wheel axle nut. Anyone able to tell me what it is? TIA

Looking for a number plate light. And also a black right hand fairing panel, that sits above the removable panel covering the fuse box. Anyone able to help? Great idea for this thread!

Away from home at the moment, so cant pop out and check.... What size are the front caliper bolts? Going to look into replacing mine as they are corroded. Cheers

G+G Premium panniers. Two 41 litre panniers with key alike locks. Full fittings for 16mm pannier racks. I had them mounted to my Givi pannier rails. Good order and watertight. I did have a very low speed off (thanks to a car hitting me on a roundabout at Dumbarton) so the right hand pannier...

Peli Case FOR SALE Peli Protector Case 1660 Comes with some of the foam lining still in it. In very good condition. It has had two holes drilled into it (one on each side under the top lip which were needed due to the contents) but I have sealed these using stainless fittings and silicon...

I seem to be in a minority, but I like my OEM panniers. However, as with most ADV riders, I have to farkle with the shiny things..... I am using LOMO dry bags which are a perfect size for siting along the top pf the panniers. But strapping them on to the top of the panniers isn't, as you...

Halvarssons Optimal Jacket in Euro 54 / UK 44 Black In very good condition and it comes with everything that it had when new. Outlast thermal liner, detachable hi-viz panel, cold weather throat storm guard. All fastenings, zips, Velcro etc are working fully. No rips or tears. It is used so...

Sorry for the short notice, but I organise a trip in Scotland each year, from another forum for my old adventure bike. This is the fifth year I've run this. We are gonna be based from a bunk house in Oban for the week. Ride outs each day, including forest roads. £15.30 per person per night...

Bike is fitted with OEM panniers and rails. I have just got hold of the DW tool box which fits on the panniers rail fittings. However, the security torx bolt heads, what size bit do I need to remove them to fit the tool box? Is it a T50? Many thanks in advance peeps.

Looking through the threads, the only info I could find on reg/rec output voltages was 14v @ 5000rpm. I am interested to know what voltage outputs others have at idle, 3000rpm and 5000rpm. My Super seems a bit slow cranking. Starts no problem, just seems a bit weak compared to my old V Twin...

Just a wee hello. Havent even picked my Super 10 up yet. Next week though! Been riding for far too many years. I have and still do tour all over Scotland. Seen a lot of the country, but still lots more to see. Moving from my old adventure bike, an ETV1000. Not sure how many forum members...